Apple Mac mini Server (Mid 2010 Specifications download pdf (Page 142)

Mac mini (Mid 2010) Take Apart — IR Board and Cable 142

2010-08-03

Removal

1 Remove 1 screw

922-8820.

2 Note the IR cable

routing on the drive

carrier.

3 Remove the IR cable

from the cable

channel.

Reassembly

The IR board must t over

the pin on the drive carrier

before securing the screw.

Important: Make sure the

grounding clip has not

been damaged and will

make contact with the

case.

1 2 ... 137 138 139 140 141 142 143 144 145 146 147 148 149 150

 Apple Technician Guide 1
Mac mini (Mid 2010) 1
Take Apart 4
About This Guide 6
Manual Updates 7
Feedback 7
Overview 9
Identifying Features 10
Product Congurations 10
Service Part Congurations 11
System Serial Number Location 11
Troubleshooting 12
General Troubleshooting 13
Common Reset Procedures 14
Wireless Troubleshooting 15
Block Diagram 16
Functional Overview 17
Symptom Charts 18
Deep Dive 19
Won’t Start Up 21
Intermittent Shutdown 23
Quick Check 25
Kernel Panic, System Crashes 28
No Video 30
Corrupted Video 31
Burnt Smell/Odor 33
Noise, Hum, Vibration 34
Uncategorized Symptoms 36
Communications 37
Ethernet Port/Device Issue 41
Uncategorized Symptom 50
Mass Storage 51
Hard Drive Read/Write Error 53
Hard Drive Noisy 54
Optical Drive Not Recognized 57
Optical Drive Noisy 63
Input/Output Devices 66
USB Devices Not Recognized 76
Mechanical 83
System Runs Hot 85
Physical Damage 86
General Information 89
Vertical Insertion 90
Low-Prole Solid 90
Platform Flex 90
Thermal Sensor Replacement 91
Logic Board Return 97
First Remove Hierarchy 98
Icon Legend 99
Bottom Cover 100
1 Lay the Mac mini 101
2 Rotate the 101
3 Press on the cover to 101
1 Replace the bottom 102
2 Rotate the cover 102
Reassembly 102
First Steps 103
1 Gently spread the 104
2 Pull the module out 104
3 Repeat to remove 104
Installation 105
1 Carefully press the 105
2 Pull the module into 105
3 Press down on the 105
4 Repeat to install the 105
1 Remove 2 T6 107
2 Carefully lift the fan 107
3 Disconnect the fan 108
Cowling 109
1 Remove the T6 screw 110
2 Lift the cowling up 110
Antenna Plate 111
1 Remove 4 screws 112
2 Carefully lift the 112
3 Disconnect the 113
1 Connect the antenna 113
2 Slide the antenna 114
3 A tool, such as the 114
4 If the plate is not 114
5 Install the 4 screws 114
Logic Board 115
1 Carefully disconnect 116
2 Make sure that at 117
3 Remove 2 T6 screws: 117
4 Remove the 2 mm 117
5 Insert the logic board 118
6 Carefully push down 118
7 Remove the tool 118
8 Disconnect the power 119
9 Important: If thermal 119
10 Push in on the catch 119
11 Once the I/O wall is 120
2010-08-03 121
1 Position the housing 122
2 Reconnect the power 122
3 Make sure no cables 122
4 Reconnect all cables 122
AirPort/Bluetooth Combo Card 123
1 Disconnect the two 124
2 Disconnect the ex 124
3 Remove 4 screws: 124
4 If the speaker has not 124
5 If replacing the ex 125
Speaker 126
1 Remove 2 screws: 127
3 Note: Check the 128
1 Insert a black stick 130
2 Grab the battery as 130
Hard Drive 131
1 Dislodge the logic 132
2 Slide out the hard 132
1 Slide hard drive 133
2 Maneuver the hard 133
3 Make sure the 133
4 Connect all cables to 133
Power Supply 134
1 Slide the power cord 135
2 Rotate the power 135
4 Pull out power supply 136
Optical Drive / 138
Hard Drive (Server) 138
2 Lift the drive and 139
3 Remove 4 T8 screws 140
4 Lift the drive from the 140
5 If replacing the 140
IR Board and Cable 141
1 Remove 1 screw 142
2 Note the IR cable 142
3 Remove the IR cable 142
1 Insert the IR cable 143
Housing 144
 Service Source 145
Exploded View 146
Exploded View (Server) 147
Screw Chart 148
External Views 149
Port View 150

Comments to this Manuals

No comments

Apple Mac mini Server (Mid 2010 Specifications Page 142

Comments to this Manuals