Apple Mac mini Server (Mid 2010 Specifications Page 139
- Page / 150
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
- Apple Technician Guide 1
- Mac mini (Mid 2010) 1
- Take Apart 4
- About This Guide 6
- Manual Updates 7
- Feedback 7
- Overview 9
- Identifying Features 10
- Product Congurations 10
- Service Part Congurations 11
- System Serial Number Location 11
- Troubleshooting 12
- General Troubleshooting 13
- Common Reset Procedures 14
- Wireless Troubleshooting 15
- Block Diagram 16
- Functional Overview 17
- Symptom Charts 18
- Deep Dive 19
- Won’t Start Up 21
- Intermittent Shutdown 23
- Quick Check 25
- Kernel Panic, System Crashes 28
- No Video 30
- Corrupted Video 31
- Burnt Smell/Odor 33
- Noise, Hum, Vibration 34
- Uncategorized Symptoms 36
- Communications 37
- Ethernet Port/Device Issue 41
- Uncategorized Symptom 50
- Mass Storage 51
- Hard Drive Read/Write Error 53
- Hard Drive Noisy 54
- Optical Drive Not Recognized 57
- Optical Drive Noisy 63
- Input/Output Devices 66
- USB Devices Not Recognized 76
- Mechanical 83
- System Runs Hot 85
- Physical Damage 86
- General Information 89
- Vertical Insertion 90
- Low-Prole Solid 90
- Platform Flex 90
- Thermal Sensor Replacement 91
- Logic Board Return 97
- First Remove Hierarchy 98
- Icon Legend 99
- Bottom Cover 100
- 1 Lay the Mac mini 101
- 2 Rotate the 101
- 3 Press on the cover to 101
- 1 Replace the bottom 102
- 2 Rotate the cover 102
- Reassembly 102
- First Steps 103
- 1 Gently spread the 104
- 2 Pull the module out 104
- 3 Repeat to remove 104
- Installation 105
- 1 Carefully press the 105
- 2 Pull the module into 105
- 3 Press down on the 105
- 4 Repeat to install the 105
- 1 Remove 2 T6 107
- 2 Carefully lift the fan 107
- 3 Disconnect the fan 108
- Cowling 109
- 1 Remove the T6 screw 110
- 2 Lift the cowling up 110
- Antenna Plate 111
- 1 Remove 4 screws 112
- 2 Carefully lift the 112
- 3 Disconnect the 113
- 1 Connect the antenna 113
- 2 Slide the antenna 114
- 3 A tool, such as the 114
- 4 If the plate is not 114
- 5 Install the 4 screws 114
- Logic Board 115
- 1 Carefully disconnect 116
- 2 Make sure that at 117
- 3 Remove 2 T6 screws: 117
- 4 Remove the 2 mm 117
- 5 Insert the logic board 118
- 6 Carefully push down 118
- 7 Remove the tool 118
- 8 Disconnect the power 119
- 9 Important: If thermal 119
- 10 Push in on the catch 119
- 11 Once the I/O wall is 120
- 2010-08-03 121
- 1 Position the housing 122
- 2 Reconnect the power 122
- 3 Make sure no cables 122
- 4 Reconnect all cables 122
- AirPort/Bluetooth Combo Card 123
- 1 Disconnect the two 124
- 2 Disconnect the ex 124
- 3 Remove 4 screws: 124
- 4 If the speaker has not 124
- 5 If replacing the ex 125
- Speaker 126
- 1 Remove 2 screws: 127
- 3 Note: Check the 128
- 1 Insert a black stick 130
- 2 Grab the battery as 130
- Hard Drive 131
- 1 Dislodge the logic 132
- 2 Slide out the hard 132
- 1 Slide hard drive 133
- 2 Maneuver the hard 133
- 3 Make sure the 133
- 4 Connect all cables to 133
- Power Supply 134
- 1 Slide the power cord 135
- 2 Rotate the power 135
- 4 Pull out power supply 136
- Optical Drive / 138
- Hard Drive (Server) 138
- 2 Lift the drive and 139
- 3 Remove 4 T8 screws 140
- 4 Lift the drive from the 140
- 5 If replacing the 140
- IR Board and Cable 141
- 1 Remove 1 screw 142
- 2 Note the IR cable 142
- 3 Remove the IR cable 142
- 1 Insert the IR cable 143
- Housing 144
- Service Source 145
- Exploded View 146
- Exploded View (Server) 147
- Screw Chart 148
- External Views 149
- Port View 150
© 2020, manymanuals.com. All rights reserved. | 0.817 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals