Apple LaserWriter Pro 630 Envelope Feeder User Manual

Service Source K Envelope Feeder LaserWriter Pro 600/630 Envelope FeederLaserWriter 16/600 PS Envelope Feeder

Take Apart Left Cover - 2 Left Cover Before you begin, remove the envelope weight.Left Cover

Take Apart Left Cover - 3 Note: Two hidden flex tabs on the bottom and two posts at the top attach the left cover to the feeder.1 Turn over the en

Take Apart Right Cover - 4 Right Cover Before you begin, remove the envelope weight.Right Cover

Take Apart Right Cover - 5 Note: Two hidden flex tabs on the bottom and two posts at the top attach the right cover to the feeder.1 Turn over the

Take Apart Front Cover - 6 Front Cover Before you begin, remove the following:• Envelope weight• Left cover• Right cover Note: If you remove the s

Take Apart Front Cover - 7 1 Remove the screw that secures the grounding cable that runs from the front cover (not shown).2 Note: This graphic sho

Take Apart Bottom Cover - 8 Bottom Cover Before you begin, remove the following:• Envelope weight• Left cover• Right cover1 Remove the four screws a

Take Apart Motor - 9 Motor Before you begin, remove the following:• Envelope weight• Left cover• Right cover• Bottom cover1 Disconnect cable J932 fr

Take Apart Sensing Arm - 10 Sensing Arm Before you begin, remove the following:• Envelope weight• Left cover• Right cover• Bottom coverSensing Arm

Take Apart Sensing Arm - 11 1 Slide out the tray extension, snap the sensing arm out of the collar grip, and lift the arm out of the feeder. Replace

Service Source K Basics Envelope Feeder

Take Apart Controller Board - 12 Controller Board Before you begin, remove the following:• Envelope weight• Left cover• Right cover• Bottom cover No

Take Apart Controller Board - 13 1 Disconnect the two cables from the controller board.2 Snap the sensing arm out of the collar grip and raise the a

Take Apart Printer Interface Cable - 14 Printer Interface Cable Before you begin, remove the following:• Envelope weight• Left cover• Right cover• B

Take Apart Printer Interface Cable - 15 1 Remove the two screws that secure the green ground wire and the ferrite core to the mounting bracket. Repl

Take Apart Pickup Rollers - 16 Pickup Rollers Before you begin, remove the following:• Envelope weight• Left cover• Right cover• Bottom coverRear Pi

Take Apart Pickup Rollers - 17 Note: The removal procedure is identical for both the rear and forward pickup rollers. The pickup rollers are inde

Take Apart Pickup Rollers - 18 2 Remove the E-ring from the end of the shaft and slide the bushing from the drive assembly plate off the end of the

Take Apart Pickup Rollers - 19 3 Raise the pickup roller shaft slightly, push it about 1/4 inch inward to clear the bushing at the opposite end, and

Take Apart Pickup Rollers - 20 Note: The LaserWriter 16/600 PS envelope feeder features a one-piece pickup roller/shaft construction, so the step

Take Apart Pickup Rollers - 21 Note: Steps 5 and 6 describe removal of a single roller. If you want to remove the middle roller, repeat these ste

Basics About This Manual - 1 About This Manual This manual covers the Take Apart, Additional Proced-ures, and Adjustments for the sheet feeder. Ref

Take Apart Pickup Rollers - 22 6 Slip the roller off the end of the shaft, and release the tabs at the shaft grooves as necessary. Replacement Note:

Take Apart Transfer Drive Assembly - 23 Transfer Drive Assembly Before you begin, remove the following:• Envelope weight• Left cover• Right cover• B

Take Apart Transfer Drive Assembly - 24 1 Remove the E-rings and bushings at the end of the three roller shafts.2 Remove the three screws that secur

Take Apart Separation Drive Assembly - 25 Separation Drive Assembly Before you begin, remove the following:• Envelope weight• Left cover• Right cove

Take Apart Separation Drive Assembly - 26 Note: The separation drive assembly receives rotational drive through the primary feed shaft. The assem

Take Apart Separation Drive Assembly - 27 1 Remove the E-rings and bushings at the end of the three roller shafts and the two screws that secure the

Take Apart Separation Drive Assembly - 28 Place your fingertips on the primary feed roller and rotate it counter to paper flow. All gears and rolle

Take Apart Primary Feed Roller - 29 Primary Feed Roller Before you begin, remove the following:• Envelope weight• Left cover• Right cover• Bottom co

Take Apart Primary Feed Roller - 30 Note: The primary feed roller is the 2-inch wide roller visible at the bottom of the three-pronged paper guide

Take Apart Primary Feed Roller - 31 1 Slide the primary feed shaft about an inch away from the motor side of the feeder and let the gear at that end

Basics Compatibility - 2 Compatibility The LaserWriter Pro 600/630 envelope feeder is compatible only with the Pro 600/630 printer. However, you ma

Take Apart Primary Feed Roller - 32 3 Note: The primary feed roller has a pinless connection (see "Slip Torque Rollers" in Basics). The

Take Apart Secondary Feed Roller - 33 Secondary Feed Roller Before you begin, remove the following:• Envelope weight• Left cover• Right cover• Botto

Take Apart Secondary Feed Roller - 34 1 Remove the E-ring and bushing at the end of the shaft near the motor and slide the shaft out of the position

Service Source K Exploded View Envelope Feeder

Exploded View 1 Exploded View Front CoverEnvelopeWeightTransfer DriveAssemblyMotorLeft CoverPickup RollersPrinterInterfaceCableRight CoverControlle

Service Source K Additional Procedures Envelope Feeder

Additional Procedures Expansion Post Connectors - 1 Expansion Post Connectors Note: This printer has several cable receptacles that are secured to

Additional Procedures Expansion Post Connectors - 2 • Fingers• Small bent-nose pliers• Grip-rings forced around the post in collar fashion• 5 mm nut

Service Source K Adjustments Envelope Feeder

Adjustments Separation Guide Opening - 1 Separation Guide Opening Note: If you have removed the separation guide plate from the front cover, you m

Basics Compatibility - 3 2 By comparing controller board serial numbers: The LaserWriter Pro 600/630 envelope feeder controller board has the vendo

Adjustments Separation Guide Opening - 2 1 Loosen the screw that secures the guide plate to the front cover.2 Insert a 1 mm and 0.5 mm thickness gau

Basics Slip Torque Rollers - 4 Slip Torque Rollers Slip torque rollers and gears are ratcheted torque-limiting gears that use bearings instead of te

Basics Slip Torque Rollers - 5 Primary Feed Roller:This roller acts independently of the shaft when the roller is rotated in reverse, thus permittin

Service Source K Take Apart Envelope Feeder

Take Apart Envelope Weight - 1 Envelope Weight No preliminary steps are required before you begin this procedure.1 Pull one of the arms out of the p