Apple Processor Cage and Clips Installation Guide download pdf (Page 21)

Home
Apple
Gateways/controllers
Processor Cage and Clips
Installation Guide

Download
Share

Sharing
Add to my manuals
Print

Required Tools

The following tools are required for installation:

• Phillips screwdriver

• Torx screwdriver

Additional requirements

If your facility or configuration requires an L5–20R plug, you must obtain a third-party L5–20R to

NEMA 5–20P adapter before installing or connecting the H5M54A 1.9kVA 120V Basic PDU.

Recommended Hardware Configurations

Configurations

The PDU is installed in a rack in the following configurations:

• A single PDU configuration, with the outlets facing the center of the rack

• A single PDU configuration, with the outlets facing the rear of the rack

Recommended Hardware Configurations 21

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 116 117

Storage Installation Guide 1
Contents 3
4 Contents 4
Contents 5 5
1 General Site Planning 6
Acclimatization 8
2 Getting Started 9
Inspecting the Packaging 10
Storage System Installation 11
Disk Drive Numbering 12
Controller Nodes 13
I/O Modules 17
Power Cooling Modules 17
Service Processor 19
Power Distribution Units 19
Important Safety Information 20
Required Tools 21
Additional requirements 21
Configurations 21
• 1U and 0U configurations 22
Hardware Installation 23
Hardware Installation 25 25
Installing the 1U and 0U PDUs 27
• 0U bracket installation 28
3. Install cage nuts 28
Securing the Cables 29
Installation is complete 30
Unpacking the Cabinet 31
Positioning the Cabinet 31
Verify the Cabling 32
Removing the Brackets 34
Installing the Rail Kit 35
Installing the Rail Kit 37 37
Installing Enclosures 38
(LFF) disk drive) 40
Installing a Disk Drive 41
NoneRound hole 43
NoneSquare hole 43
ScrewdriverThreaded hole 43
• Screwdriver 44
7 Cabling the Storage System 50
Cabling Expansion Cabinets 51
Cabling the Service Processor 52
Cabling the Power Strips 53
Verifying Setup 54
Verifying LED Status 56
Figure 37 Disk Drive LEDs 57
Table 9 PCM LED Descriptions 58
Node Interconnect Ports 60
Drive Enclosure LEDs 61
Figure 42 Front Panel LEDs 62
Table 11 Front panel LEDs 62
Figure 43 Rear Panel LEDs 63
Table 12 Rear panel LEDs 63
Prerequisites for Using a VSP 64
Deploying the VSP OVF File 65
Launching HP 3PAR SmartStart 72
Generate Service Processor ID 75
Configure SP Networking 76
Remote Support 77
System Support Information 79
Time and Region 80
Change Passwords 81
Applying Settings 83
Figure 57 Apply Settings 84
Verify Storage System 88
Configure Networking 89
◦ Subnet Mask 89
◦ Gateway 89
Configuring Time 89
Figure 65 Configure Time Page 90
Change Password 91
Verify Configuration 92
Progress 92
Figure 68 Progress Page 93
Figure 69 Results Page 93
Contacting HP 95
HP 3PAR documentation 95
Typographic conventions 98
HP 3PAR branding information 98
12 Documentation feedback 99
Figure 74 7000 Series PCM 101
Figure 75 M6700 Series PCM 102
Figure 77 SFF Drive Assembly 102
Figure 79 LFF Drive Assembly 103
Accessory Kits 104
Rail Kits 104
Rail Kits 105 105
Figure 87 M5 Cage Nut 106
Adding Disk Drives 110
Checking Progress 111
Completing the Upgrade 112
SmartStart is Unavailable 113
E Validating Remote Support 114
G Troubleshooting 117

Comments to this Manuals

No comments

Apple Processor Cage and Clips Installation Guide Page 21

Comments to this Manuals